Toyota Tarago (Previa) 98

14 Янв 2015 | Author: | No comments yet »
Toyota Previa/tarago

Friday, January 2, 2009

Stereo From 98 Tarago

This is a guide detailing how to and replace the stereo head of a 98 Toyota Tarago (Previa or Tarago is what they are in Australia.

From my research is not much difference between the so this guide should be to all Tarago’s between 90-99 am not 100% certain).

I have this guide because i able to find any FULL on how to replace the stereo and thought i make a nice simple

Equipment needed:

The following is what is required. It contains the that you would need for any removable from a car.

/ Flat Head Screw

Wire Cutters

Wire

Electrical Tape

Soldering

Solder

Spanner (to remove from battery)

A LOT OF PATIENCE

Steps in removing

Step 1

Start of be removing the parts, which consist of the cover, the ash tray and the glove box

To remove the fuse cover the tab at the front and lift the lid up.

If you have an light, disconnect it by pushing tab at the

Place the lid in a safe place.

the ash tray out and push down on the tab and the tray out.


Using a head screw driver, the socket where it holds the box out, while at the same pulling that side of the box out. This side pop out and the glove box will come

Step 2

Now we have to remove 6 The screws location are shown by the

The screw located under the lighter is on an angle but shouldn’t any problems removing it.

Step 3

Now is the hardest part of the entire Removing the cup holder/ cigarette / component. I had difficulties removing part and was unsuccessful at my first After letting a couple of go by, i decided to attempt it again. minutes into my second i removed it without any hustles. If you do it take a break, this help you relax and stop from forcing it and damaging the or to surrounding plastics.

Behind the cigarette lighter their is a clip containing the two cables. this by pulling the clip

Try to remember how you took it out so you can put it back in

Open the cup holder. (Notice the pointed out)

Push the back and towards the right so its starts to look like

Further more pushing to the and back will further push the component:

By now it will like this:

It is now nearly all you really have to do is keep it back and towards the right the left side is no longer by the side wall. Then you simply remove it.

Step 4

there are two screws that are the entire middle console.

I was to undo the screws with a driver as they were to and the screw driver kept I used a 8mm socket and wrench to the screws. Once thy were i used the screw driver to them.

You must push tabs with one hand with the other hand the middle console out. some jiggling the middle will pop out. Once it you can pull it out with both

Remove the antenna by pulling it.

7

Remove the bracket that the head unit to the middle compartment by removing the 4 screws (2 on side) that hold the in place.

Step 8

Remove the 4 that hold the head to the bracket.

Using a flat screw driver, place it the metal screw and pull it up, leverage. Pull the head out.

Step 9

Place new head unit into the (if you have to, you may need to push the tabs flat). Screw the back onto the center and your head unit now sit nicely in its new home. (My head fitted into the existing i don’t know how other units will fit)

10

Now you have to connect your new unit to the existing cables. sure your battery is so you don’t short circuit Solder your connections to a good solid connection and them in electrical tape. done connect your unit and connect the battery and test your new unit to sure it works (Test all are working etc). Once is done you can put everything back in

This diagram is for 1998 (Australian). It might be different for models so please be be careful using it for other models.

11

Place the center console in.

Put one side of the air duct into (making sure you don’t the foam) and push the opposite in gently or you will damage the

Put back the two screws that go

Step 12

Now you have to put back in the cup it is pretty mush the reverse of how you it out, again be patient you get it back in.

Connect your cigarette cable clip back.

back all 6 screws.

Put you glove box by putting one side into the and pushing the other side in.

Put back you ash tray and fuse remembering to connect back alarm light if you have

Step 13

Enjoy your new unit.

Toyota Previa/tarago
Toyota Previa/tarago

Interesting Articles

Here you can write a commentary on the recording "Toyota Tarago (Previa) 98".

Sign in, to write a review.

Twitter-news
Our partners
Follow us
Contact us
Our contacts

dima911@gmail.com

Born in the USSR

423360519

About this site

For all questions about advertising, please contact listed on the site.


Toyota cars catalog with specifications, pictures, ratings, reviews and discusssions about cars Toyota.